PSN-L Email List Message
Subject: Re: "P" ky "Slinky"
From: tchannel1@............
Date: Thu, 26 Jul 2007 12:57:02 -0600
Hi Folks, Sorry about the drawing I will repost it, including the left =
hand side which got cut off...I will also try to clean it up a bit. =
And more pictures. This is just an idea sketch.
We all learn things which are undeniable truths.....One for me is " I =
must always make something three times to get it right" Maybe that's =
were they get "the third times a charm"
Anyhow, I would like to make another, so if someone is interested in =
this concept, let me know and maybe I can help with some of the parts. =
If someone has limited tools etc.
Paul C. suggested I use two ring magnets, one entering the top of the =
coil, and the other exiting the bottom of the coil.
I started with one magnet 1/2 (deep inside the coil), but I did not like =
the results. I then moved the magnet to the top of the coil, just =
entering, that worked better. I then added another magnet, two =
together, 1 and 1/2 magnets inside the top of the coil. This worked =
well. To try Paul's idea, I would just need to open it up and move =
the spacing nuts and magnets.
To many details for this email, but its basically simple. A 12" brass =
threaded rod hangs inside the two tees, on which are brass spacing nuts, =
and three ring magnets. Two for the coil and one for the damper.
Another thing I would maybe do different is to use the 3" black ABS? =
pipe and tees, as they are thicker wall and straighter.
With the rod+magnets+nuts there was no more room for a mass. I tried =
addition mass and it pulled the spring too long. I wanted to limit the =
total height to 7', but cut it down to 5'....I think at 7' the period =
was 2.4, and at 5' it was 2.2?
Thanks, Ted So give me a little time and check the site =
again..........http://picasaweb.google.com/tchannel33
----- Original Message -----=20
From: ChrisAtUpw@..........
To: psn-l@.................
Sent: Thursday, July 26, 2007 10:36 AM
Subject: Re: "P" ky "Slinky"
In a message dated 2007/07/26, tchannel1@............ writes:
http://picasaweb.google.com/tchannel33 I have posted some picture =
here. Just click on the album call "5' Slinky" and you can see 9 =
pictures, I hope.=20
Hi Ted,
The photos are OK , but the diagram is unreadable. It won't =
even print out.
Regards,
Hi Folks, Sorry about the drawing =
I will=20
repost it, including the left hand side which got cut off...I will =
also=20
try to clean it up a bit. And more =
pictures. =20
This is just an idea sketch.
We all learn things which are =
undeniable=20
truths.....One for me is " I must always make something three times to =
get it=20
right" Maybe that's were they get "the third times a=20
charm"
Anyhow, I would like to =
make another,=20
so if someone is interested in this concept, let me know and maybe =
I can=20
help with some of the parts. If someone has limited tools=20
etc.
Paul C. suggested I use two ring =
magnets, one=20
entering the top of the coil, and the other exiting the bottom of the=20
coil.
I started with one magnet 1/2 (deep =
inside the=20
coil), but I did not like the results. I then moved the magnet to =
the top=20
of the coil, just entering, that worked better. I then added =
another=20
magnet, two together, 1 and 1/2 magnets inside the top of the=20
coil. This worked well. To try Paul's =
idea, =20
I would just need to open it up and move the spacing nuts and=20
magnets.
To many details for this email, but its =
basically=20
simple. A 12" brass threaded rod hangs inside the two tees, =
on which=20
are brass spacing nuts, and three ring magnets. Two for the coil =
and one=20
for the damper.
Another thing I would maybe do =
different is to use=20
the 3" black ABS? pipe and tees, as they are thicker wall and =
straighter.
With the rod+magnets+nuts there was no =
more room=20
for a mass. I tried addition mass and it pulled the spring too =
long. =20
I wanted to limit the total height to 7', but cut it down to 5'....I =
think at 7'=20
the period was 2.4, and at 5' it was 2.2?
Thanks, Ted So =
give me a=20
little time and check the site=20
again..........http://picasaweb.google.com/tchannel33
----- Original Message -----
Sent: Thursday, July 26, 2007 =
10:36=20
AM
Subject: Re: "P" ky =
"Slinky"
In a=20
message dated 2007/07/26, tchannel1@............=20
writes:
http://picasaweb.google.c=
om/tchannel33 =20
I have posted some picture here. Just click on the album call =
"5'=20
Slinky" and you can see 9 pictures, I hope.
Hi=20
Ted,
The photos are OK , =
but the=20
diagram is unreadable. It won't even print=20
out.
=20
Regards,
Chris =
Chapman=20
[ Top ]
[ Back ]
[ Home Page ]